The 'gcode_variable' section is not available in all Klipper versions.
Removed it and simplified KNCM_settings.cfg to use direct defaults.
Also reverted to 'probe:z_virtual_endstop' which is correct when
[mcu rpi] is defined in printer.cfg.
Changes:
- KNCM_settings.cfg: Removed [gcode_variable printer_settings]
- user_settings_clean.cfg: endstop_pin: probe:z_virtual_endstop
- optimized_user_settings.cfg: endstop_pin: probe:z_virtual_endstop
Created KNCM_settings.cfg with essential macros:
- CLEAN_NOZZLE: Wipe nozzle on brush/cloth
- SMART_PARK: Park nozzle at front for easy access
- LINE_PURGE: Print purge line at start
- Frame_Light_ON/OFF: Control frame LED (PD14)
- Part_Light_ON/OFF: Control part light (PD13)
Also added [output_pin] definitions for lights:
- frame_light: PD14
- part_light: PD13
This fixes: 'Unknown pin chip name rpi' error caused by
missing KNCM_settings.cfg include.
The file was previously included but didn't exist in the repo.
The Cartographer plugin registers as 'cartographer', not 'probe'.
Using 'probe:' causes: 'Unknown pin chip name probe'
Correct syntax:
endstop_pin: cartographer:z_virtual_endstop
The Neptune 4 Plus has a built-in ADXL345 accelerometer on the
mainboard. This is more reliable than the Cartographer integrated
ADXL which has version-specific pin requirements (V3: PA3, V4: PA0).
Configuration:
- cs_pin: PG11 (Neptune 4 Plus mainboard ADXL)
- spi_bus: spi2
The Cartographer ADXL config is kept as a commented alternative
for users who prefer to use it.
This fixes: 'Invalid adxl345 id (got 0 vs e5)' errors by using
the known-working mainboard accelerometer.
According to official Cartographer documentation:
- Cartographer V3: cs_pin: cartographer:PA3
- Cartographer V4: cs_pin: cartographer:PA0
Using the wrong pin causes: 'Invalid adxl345 id (got 0 vs e5)'
Added clear documentation in both user_settings_clean.cfg and
optimized_user_settings.cfg to help users select the correct pin.
Reference: https://docs.cartographer3d.com/cartographer-probe/installation-and-setup/software-configuration/klipper-setup
The 'accel_chip' option is not valid in [cartographer] section.
ADXL345 must be configured as a separate [adxl345] device that
communicates via the Cartographer MCU.
Correct configuration:
- [adxl345] with cs_pin: cartographer:PA3 and spi_bus: spi1
- [resonance_tester] with accel_chip: adxl345
- [cartographer] does NOT include accel_chip
This fixes: 'Option accel_chip is not valid in section cartographer'
The ADXL345 accelerometer is built into the Cartographer probe.
It must be configured within the [cartographer] section, not as
a separate [adxl345] device.
Changes:
- Added 'accel_chip: adxl345' to [cartographer] section
- Removed separate [adxl345] section (no longer needed)
- Changed [resonance_tester] to use 'accel_chip: cartographer'
- Added default probe_points for resonance testing
This fixes: 'Invalid adxl345 id (got 0 vs e5)' error
Reference: https://docs.cartographer3d.com/
The 'group' attribute is not supported in all Klipper versions.
This caused: 'Option group is not valid in section gcode_macro'
Macros will appear under 'Uncategorized' in Mainsail/Fluidd
until Klipper adds official support for macro grouping.
Combined best features from printer.cfg PRINT_END and custom version:
From printer.cfg:
- END_TUNE beeper jingle
- Park position X0 Y315 (better visibility)
From custom version:
- Detailed console/LCD messages
- M84 to disable steppers
- Higher Z-park (10mm)
- Both Frame_Light and Part_Light OFF
- Filament sensors disabled
Usage: Call PRINT_END_NOCCI in slicer end gcode
- Added [include calibration/*.cfg] to optimized_user_settings.cfg
- Updated CHANGES.md with complete deployment steps
- Updated calibration/README.md with installation options
Now the calibration macros are automatically available when using
the optimized user_settings.cfg - no manual include needed!
- SET_GCODE_OFFSET Z=0 for consistent Z-Offset reset
- CG28 instead of G28 (Open4Neptune smart home)
- CARTOGRAPHER_TOUCH_HOME for precise Z0 measurement
- Tighter temperature tolerance (±2°C vs ±4-10°C)
- Full documentation in CHANGES.md
