f05f64c3b2
- Added [include calibration/*.cfg] to optimized_user_settings.cfg - Updated CHANGES.md with complete deployment steps - Updated calibration/README.md with installation options Now the calibration macros are automatically available when using the optimized user_settings.cfg - no manual include needed!
124 lines
3.8 KiB
Markdown
124 lines
3.8 KiB
Markdown
# 📝 Changes for PRINT_START_NOCCI
|
|
|
|
## 🎯 Optimizations Applied (2026-03-12)
|
|
|
|
### Key Changes in `optimized_user_settings.cfg`:
|
|
|
|
| Line | Change | Reason |
|
|
|------|--------|--------|
|
|
| 5 | `SET_GCODE_OFFSET Z=0` added | Reset Z-Offset before every print (Cartographer best practice) |
|
|
| 9 | `G28` → `CG28` | Use Open4Neptune smart home command |
|
|
| 10 | `CARTOGRAPHER_TOUCH_HOME` added | Precise Z0 measurement with Cartographer sensor |
|
|
| 35-36 | Temp tolerance `±4-10°C` → `±2°C` | Tighter temperature control for consistent starts |
|
|
|
|
### Full Optimized Macro:
|
|
|
|
```klipper
|
|
[gcode_macro PRINT_START_NOCCI]
|
|
gcode:
|
|
#--- Setup & Reset ---
|
|
M117 Setting up parameters...
|
|
RESPOND MSG="Starting Print Sequence..."
|
|
|
|
SET_GCODE_OFFSET Z=0 ; ⭐ NEW: Reset Z-Offset for Cartographer
|
|
G92 E0
|
|
G90 ; Absolute positioning
|
|
BED_MESH_CLEAR
|
|
Frame_Light_ON
|
|
Part_Light_ON
|
|
|
|
#--- Home with Cartographer ---
|
|
CG28 ; ⭐ CHANGE: G28 → CG28 (Open4Neptune smart home)
|
|
CARTOGRAPHER_TOUCH_HOME ; ⭐ NEW: Precise Z0 measurement with Cartographer
|
|
|
|
#--- Parameters ---
|
|
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
|
|
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(200)|float %}
|
|
{% set FILAMENT_TYPE = params.FILAMENT_TYPE|default("PLA")|upper %}
|
|
|
|
#--- Pre-Heat ---
|
|
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=160 ; No-drip pre-heat
|
|
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={BED_TEMP}
|
|
|
|
#--- Wait for Bed & Mesh ---
|
|
{% set MIN_TEMP = BED_TEMP - (BED_TEMP * 0.15) %}
|
|
TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={MIN_TEMP}
|
|
BED_MESH_CALIBRATE ADAPTIVE=1
|
|
|
|
#--- Nozzle Clean (KNCM) ---
|
|
CLEAN_NOZZLE FILAMENT_TYPE={FILAMENT_TYPE}
|
|
|
|
#--- Final Heat ---
|
|
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={EXTRUDER_TEMP}
|
|
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={EXTRUDER_TEMP-2} MAXIMUM={EXTRUDER_TEMP+2} ; ⭐ TIGHTER: ±2°C
|
|
TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={BED_TEMP-2} MAXIMUM={BED_TEMP+2} ; ⭐ TIGHTER: ±2°C
|
|
|
|
#--- Prime & Start ---
|
|
SMART_PARK
|
|
SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=1
|
|
SET_FILAMENT_SENSOR SENSOR=filament_motion ENABLE=0
|
|
LINE_PURGE
|
|
G92 E0
|
|
G1 Z2.0 F3000
|
|
|
|
M117 Printer goes brrbrrr...:)
|
|
RESPOND MSG="Print starting..."
|
|
```
|
|
|
|
## 📋 Deployment Steps:
|
|
|
|
1. **Backup current config:**
|
|
```bash
|
|
cd ~/printer_data/config
|
|
cp user_settings.cfg user_settings.cfg.backup-$(date +%Y%m%d)
|
|
```
|
|
|
|
2. **Clone repo (if not done):**
|
|
```bash
|
|
cd ~/printer_data/config
|
|
git clone https://git.sky-net.it/nocci/open4neptune-new.git
|
|
```
|
|
|
|
3. **Copy calibration folder:**
|
|
```bash
|
|
cp -r open4neptune-new/calibration/ ~/printer_data/config/
|
|
```
|
|
|
|
4. **Copy optimized user_settings.cfg:**
|
|
```bash
|
|
cp open4neptune-new/optimized_user_settings.cfg ~/printer_data/config/user_settings.cfg
|
|
```
|
|
|
|
5. **Restart Klipper:**
|
|
- Via Mainsail/Fluidd: Machine → Restart Firmware
|
|
- Or SSH: `sudo systemctl restart klipper`
|
|
|
|
6. **Test calibration macros:**
|
|
```gcode
|
|
; In Mainsail Console:
|
|
CALIBRATION_MENU
|
|
```
|
|
|
|
7. **Test print** and observe:
|
|
- Check console for "Starting Print Sequence..."
|
|
- Verify Cartographer Touch Home runs
|
|
- Monitor temperature wait times
|
|
|
|
## 🔧 What This Improves:
|
|
|
|
- **Better Z accuracy** with Cartographer Touch Home
|
|
- **Consistent Z-Offset** reset before each print
|
|
- **Tighter temperature control** (±2°C vs ±4-10°C)
|
|
- **Smart homing** with CG28 (skips if already homed)
|
|
|
|
## ⚠️ Notes:
|
|
|
|
- Keep `printer.cfg` untouched (Open4Neptune updates will overwrite it)
|
|
- Only `user_settings.cfg` contains your customizations
|
|
- Backup before Open4Neptune updates!
|
|
|
|
---
|
|
Created: 2026-03-12
|
|
Printer: Neptune 4 Plus
|
|
Probe: Cartographer 3D
|
|
Firmware: Open4Neptune
|